Juniper : Security Vulnerabilities, CVEs, CVSS score between 1 and 4.99

A Missing Authentication for Critical Function vulnerability in the Packet Forwarding Engine (pfe) of Juniper Networks Junos OS on MX Series with SPC3, and SRX Series allows an unauthenticated network-based attacker to cause limited impact to the integrity or availability of the device. If a device is configured with IPsec authentication algorithm hmac-sha-384 or hmac-sha-512, tunnels are established normally but for traffic traversing the tunnel no authentication information is sent with the encrypted data on egress, and no authentication information is expected on ingress. So if the peer is an unaffected device transit traffic is going to fail in both directions. If the peer is an also affected device transit traffic works, but without authentication, and configuration and CLI operational commands indicate authentication is performed. This issue affects Junos OS: All versions before 20.4R3-S7, 21.1 versions before 21.1R3,  21.2 versions before 21.2R2-S1, 21.2R3,  21.3 versions before 21.3R1-S2, 21.3R2.

A Use of an Uninitialized Resource vulnerability in the routing protocol daemon (rpd) of Juniper Networks Junos OS and Junos OS Evolved allows a local, authenticated attacker with low privileges to cause a Denial of Service (DoS). On all Junos OS and Junos OS Evolved platforms, in a Multicast only Fast Reroute (MoFRR) scenario, the rpd process can crash when a a specific low privileged CLI command is executed. The rpd crash will impact all routing protocols until the process has automatically been restarted. As the operational state which makes this issue exploitable is outside the attackers control, this issue is considered difficult to exploit. Continued execution of this command will lead to a sustained DoS. This issue affects: Juniper Networks Junos OS 19.4 version 19.4R3-S5 and later versions prior to 19.4R3-S9; 20.1 version 20.1R2 and later versions; 20.2 versions prior to 20.2R3-S7; 20.3 versions prior to 20.3R3-S5; 20.4 versions prior to 20.4R3-S6; 21.1 versions prior to 21.1R3-S4; 21.2 versions prior to 21.2R3-S2; 21.3 versions prior to 21.3R3-S1; 21.4 versions prior to 21.4R3; 22.1 versions prior to 22.1R1-S2, 22.1R2; 22.2 versions prior to 22.2R2. Juniper Networks Junos OS Evolved All versions prior to 20.4R3-S6-EVO; 21.1-EVO version 21.1R1-EVO and later versions; 21.2-EVO version 21.2R1-EVO and later versions; 21.3-EVO versions prior to 21.3R3-S1-EVO; 21.4-EVO versions prior to 21.4R3-EVO; 22.1-EVO versions prior to 22.1R1-S2-EVO, 22.1R2-EVO; 22.2-EVO versions prior to 22.2R2-EVO.

An Improper Check for Unusual or Exceptional Conditions vulnerability in the kernel of Juniper Networks Junos OS allows an adjacent unauthenticated attacker to bypass an integrity check. In a 6PE scenario and if an additional integrity check is configured, it will fail to drop specific malformed IPv6 packets, and then these packets will be forwarded to other connected networks. This issue affects Juniper Networks Junos OS: All versions prior to 19.3R3-S7; 19.4 versions prior to 19.4R3-S9; 20.2 versions prior to 20.2R3-S7; 20.3 versions prior to 20.3R3-S5; 20.4 versions prior to 20.4R3-S4; 21.1 versions prior to 21.1R3-S3; 21.2 versions prior to 21.2R3-S2; 21.3 versions prior to 21.3R3-S1; 21.4 versions prior to 21.4R2-S1, 21.4R3; 22.1 versions prior to 22.1R2; 22.2 versions prior to 22.2R2.

An Unexpected Status Code or Return Value vulnerability in the kernel of Juniper Networks Junos OS allows an unauthenticated attacker with physical access to the device to cause a Denial of Service (DoS). When certain USB devices are connected to a USB port of the routing-engine (RE), the kernel will crash leading to a reboot of the device. The device will continue to crash as long as the USB device is connected. This issue affects Juniper Networks Junos OS: All versions prior to 19.4R3-S10; 20.2 versions prior to 20.2R3-S7; 20.3 versions prior to 20.3R3-S6; 20.4 versions prior to 20.4R3-S5; 21.1 versions prior to 21.1R3-S4; 21.2 versions prior to 21.2R3-S4; 21.3 versions prior to 21.3R3-S3; 21.4 versions prior to 21.4R3-S2; 22.1 versions prior to 22.1R2-S2, 22.1R3; 22.2 versions prior to 22.2R2, 22.2R3; 22.3 versions prior to 22.3R1-S1, 22.3R2; 22.4 versions prior to 22.4R2.

A Path Traversal vulnerability in the J-Web component of Juniper Networks Junos OS allows an authenticated attacker to upload arbitrary files to the device by bypassing validation checks built into Junos OS. The attacker should not be able to execute the file due to validation checks built into Junos OS. Successful exploitation of this vulnerability could lead to loss of filesystem integrity. This issue affects Juniper Networks Junos OS: all versions prior to 19.1R3-S9; 19.2 versions prior to 19.2R3-S6; 19.3 versions prior to 19.3R3-S7; 19.4 versions prior to 19.4R3-S9; 20.1 versions prior to 20.1R3-S5; 20.2 versions prior to 20.2R3-S5; 20.3 versions prior to 20.3R3-S5; 20.4 versions prior to 20.4R3-S4; 21.1 versions prior to 21.1R3-S2; 21.2 versions prior to 21.2R3-S1; 21.3 versions prior to 21.3R2-S2, 21.3R3; 21.4 versions prior to 21.4R1-S2, 21.4R2-S1, 21.4R3; 22.1 versions prior to 22.1R1-S1, 22.1R2.

An XPath Injection vulnerability due to Improper Input Validation in the J-Web component of Juniper Networks Junos OS allows an authenticated attacker to add an XPath command to the XPath stream, which may allow chaining to other unspecified vulnerabilities, leading to a partial loss of confidentiality. This issue affects Juniper Networks Junos OS: all versions prior to 19.1R3-S9; 19.2 versions prior to 19.2R3-S6; 19.3 versions prior to 19.3R3-S7; 19.4 versions prior to 19.4R2-S7, 19.4R3-S8; 20.1 versions prior to 20.1R3-S5; 20.2 versions prior to 20.2R3-S5; 20.3 versions prior to 20.3R3-S5; 20.4 versions prior to 20.4R3-S4; 21.1 versions prior to 21.1R3-S2; 21.2 versions prior to 21.2R3-S1; 21.3 versions prior to 21.3R2-S2, 21.3R3; 21.4 versions prior to 21.4R1-S2, 21.4R2-S1, 21.4R3; 22.1 versions prior to 22.1R1-S1, 22.1R2.

An Exposure of Sensitive Information to an Unauthorized Actor vulnerability in the PFE of Juniper Networks Junos OS on PTX Series and QFX10k Series allows an adjacent unauthenticated attacker to gain access to sensitive information. PTX1000 and PTX10000 Series, and QFX10000 Series and PTX5000 Series devices sometimes do not reliably pad Ethernet packets, and thus some packets can contain fragments of system memory or data from previous packets. This issue is also known as 'Etherleak' and often detected as CVE-2003-0001. This issue affects: Juniper Networks Junos OS on PTX1000 and PTX10000 Series: All versions prior to 18.4R3-S11; 19.1 versions prior to 19.1R2-S3, 19.1R3-S7; 19.2 versions prior to 19.2R1-S8, 19.2R3-S4; 19.3 versions prior to 19.3R3-S4; 19.4 versions prior to 19.4R2-S5, 19.4R3-S6; 20.1 versions prior to 20.1R3-S2; 20.2 versions prior to 20.2R3-S3; 20.3 versions prior to 20.3R3-S2; 20.4 versions prior to 20.4R3-S4; 21.1 versions prior to 21.1R2-S1, 21.1R3; 21.2 versions prior to 21.2R1-S1, 21.2R2. Juniper Networks Junos OS on QFX10000 Series and PTX5000 Series: All versions prior to 18.3R3-S6; 18.4 versions prior to 18.4R2-S9, 18.4R3-S10; 19.1 versions prior to 19.1R2-S3, 19.1R3-S7; 19.2 versions prior to 19.2R1-S8, 19.2R3-S4; 19.3 versions prior to 19.3R3-S4; 19.4 versions prior to 19.4R2-S6, 19.4R3-S6; 20.1 versions prior to 20.1R3-S2; 20.2 versions prior to 20.2R3-S3; 20.3 versions prior to 20.3R3-S1; 20.4 versions prior to 20.4R3-S1; 21.1 versions prior to 21.1R2-S1, 21.1R3; 21.2 versions prior to 21.2R2.

A Race Condition in the 'show chassis pic' command in Juniper Networks Junos OS Evolved may allow an attacker to crash the port interface concentrator daemon (picd) process on the FPC, if the command is executed coincident with other system events outside the attacker's control, leading to a Denial of Service (DoS) condition. Continued execution of the CLI command, under precise conditions, could create a sustained Denial of Service (DoS) condition. This issue affects all Juniper Networks Junos OS Evolved versions prior to 20.1R2-EVO on PTX10003 and PTX10008 platforms. Junos OS is not affected by this vulnerability.

Improper Handling of Unexpected Data in the firewall policer of Juniper Networks Junos OS on EX4300 switches allows matching traffic to exceed set policer limits, possibly leading to a limited Denial of Service (DoS) condition. When the firewall policer discard action fails on a Layer 2 port, it will allow traffic to pass even though it exceeds set policer limits. Traffic will not get discarded, and will be forwarded even though a policer discard action is configured. When the issue occurs, traffic is not discarded as desired, which can be observed by comparing the Input bytes with the Output bytes using the following command: user@junos> monitor interface traffic Interface Link Input bytes (bps) Output bytes (bps) ge-0/0/0 Up 37425422 (82616) 37425354 (82616) <<<< egress ge-0/0/1 Up 37425898 (82616) 37425354 (82616) <<<< ingress The expected output, with input and output counters differing, is shown below: Interface Link Input bytes (bps) Output bytes (bps) ge-0/0/0 Up 342420570 (54600) 342422760 (54600) <<<< egress ge-0/0/1 Up 517672120 (84000) 342420570 (54600) <<<< ingress This issue only affects IPv4 policing. IPv6 traffic and firewall policing actions are not affected by this issue. This issue affects Juniper Networks Junos OS on the EX4300: All versions prior to 17.3R3-S10; 17.4 versions prior to 17.4R3-S3; 18.1 versions prior to 18.1R3-S11; 18.2 versions prior to 18.2R3-S6; 18.3 versions prior to 18.3R3-S4; 18.4 versions prior to 18.4R3-S6; 19.1 versions prior to 19.1R3-S3; 19.2 versions prior to 19.2R3-S1; 19.3 versions prior to 19.3R3-S1; 19.4 versions prior to 19.4R3; 20.1 versions prior to 20.1R2; 20.2 versions prior to 20.2R2.

Version 4.40 of the TPM (Trusted Platform Module) firmware on Juniper Networks SRX300 Series has a weakness in generating cryptographic keys that may allow an attacker to decrypt sensitive information in SRX300 Series products. The TPM is used in the SRX300 Series to encrypt sensitive configuration data. While other products also ship with a TPM, no other products or platforms are affected by this vulnerability. Customers can confirm the version of TPM firmware via the 'show security tpm status' command. This issue was discovered by an external security researcher. No other Juniper Networks products or platforms are affected by this issue.

The Secure Meeting (Pulse Collaboration) in Pulse Connect Secure (formerly Juniper Junos Pulse) before 7.1R22.1, 7.4, 8.0 before 8.0R11, and 8.1 before 8.1R3 allows remote authenticated users to bypass intended access restrictions and log into arbitrary meetings by leveraging a meeting id and meetingAppSun.jar.

Pulse Connect Secure (aka PCS and formerly Juniper PCS) PSC6000, PCS6500, and MAG PSC360 8.1 before 8.1r5, 8.0 before 8.0r13, 7.4 before 7.4r13.5, and 7.1 before 7.1r22.2 and PPS 5.1 before 5.1R5 and 5.0 before 5.0R13, when Hardware Acceleration is enabled, does not properly validate the Finished TLS handshake message, which makes it easier for remote attackers to conduct man-in-the-middle attacks via a crafted Finished message.

Cross-site scripting (XSS) vulnerability in the Dynamic VPN in Juniper Junos 12.1X44 before 12.1X44-D45, 12.1X46 before 12.1X46-D30, 12.1X47 before 12.1X47-D20, and 12.3X48 before 12.3X48-D10 on SRX series devices allows remote attackers to inject arbitrary web script or HTML via unspecified vectors.

J-Web in Juniper Junos 11.4 before 11.4R12, 12.1X44 before 12.1X44-D35, 12.1X46 before 12.1X46-D25, 12.1X47 before 12.1X47-D10, 12.3X48 before 12.3X48-D10, 12.2 before 12.2R9, 12.3 before 12.3R7, 13.2 before 13.2R6, 13.2X51 before 13.2X51-D20, 13.3 before 13.3R5, 14.1 before 14.1R3, 14.1X53 before 14.1X53-D10, and 14.2 before 14.2R1 allows remote attackers to conduct clickjacking attacks via an X-Frame-Options header.

Unspecified vulnerability in Oracle MySQL Server 5.5.43 and earlier and 5.6.23 and earlier allows remote authenticated users to affect confidentiality via unknown vectors related to Server : Security : Privileges.

Unspecified vulnerability in Oracle MySQL Server 5.5.39 and earlier, and 5.6.20 and earlier, allows remote attackers to affect confidentiality via vectors related to C API SSL CERTIFICATE HANDLING.

Unspecified vulnerability in Oracle MySQL Server 5.5.39 and earlier, and 5.6.20 and earlier, allows remote attackers to affect availability via vectors related to CLIENT:SSL:yaSSL, a different vulnerability than CVE-2014-6494.

Unspecified vulnerability in Oracle MySQL Server 5.5.38 and earlier, and 5.6.19 and earlier, allows remote attackers to affect availability via vectors related to SERVER:SSL:yaSSL.

Unspecified vulnerability in Oracle MySQL Server 5.5.39 and earlier, and 5.6.20 and earlier, allows remote attackers to affect availability via vectors related to CLIENT:SSL:yaSSL, a different vulnerability than CVE-2014-6496.

Unspecified vulnerability in Oracle MySQL Server 5.5.38 and earlier, and 5.6.19 and earlier, allows remote attackers to affect integrity via vectors related to SERVER:SSL:yaSSL.

Juniper WLC devices with WLAN Software releases 8.0.x before 8.0.4, 9.0.x before 9.0.2.11, 9.0.3.x before 9.0.3.5, and 9.1.x before 9.1.1, when "Proxy ARP" or "No Broadcast" features are enabled in a clustered setup, allows remote attackers to cause a denial of service (device disconnect) via unspecified vectors.

Cross-site scripting (XSS) vulnerability in the web server in the Juniper Junos Pulse Secure Access Service (SSL VPN) devices with IVE OS 8.0 before 8.0r6, 7.4 before 7.4r13, and 7.1 before 7.1r20 allows remote attackers to inject arbitrary web script or HTML via unspecified vectors.

The Juniper Junos Pulse Secure Access Service (SSL VPN) devices with IVE OS 8.0 before 8.0r1, 7.4 before 7.4r5, and 7.1 before 7.1r18 allows remote attackers to conduct clickjacking attacks via unspecified vectors.

Cross-site scripting (XSS) vulnerability in SRX Web Authentication (webauth) in Juniper Junos 11.4 before 11.4R11, 12.1X44 before 12.1X44-D34, 12.1X45 before 12.1X45-D25, 12.1X46 before 12.1X46-D20, and 12.1X47 before 12.1X47-D10 allows remote attackers to inject arbitrary web script or HTML via unspecified vectors.

Cross-site scripting (XSS) vulnerability in the SSL VPN/UAC web server in the Juniper Junos Pulse Secure Access Service (SSL VPN) devices with IVE OS 7.1 before 7.1r16, 7.4 before 7.4r3, and 8.0 before 8.0r1 and the Juniper Junos Pulse Access Control Service devices with UAC OS 4.1 before 4.1r8, 4.4 before 4.4r3 and 5.0 before 5.0r1 allows remote administrators to inject arbitrary web script or HTML via unspecified vectors.